KeystoneMold
2026-11-04 · 6 min read

What tolerance can a mold component shop actually hold?

Anyone can claim 0.002 mm. The useful question is which operation holds it, on which feature, and who measures it. Here is how to read a tolerance claim.

← All insights

When a supplier's website says “tolerance: 0.002 mm”, that number usually describes one machine, not the part you are buying. It is worth knowing which operation can actually hold what, because the answer changes the price and the lead time.

Tolerance follows the operation, not the company

OperationWhat it realistically holdsNotes
CNC milling±0.01 mm±0.005 mm on a good machine with careful setup, at higher cost
CNC turning±0.01 mmBetter on diameter than on length
Surface grinding0.002–0.003 mmThe most reliable route to tight flatness and parallelism
Wire EDM (fast)±0.01 mmFast, cheap, suitable for profiles
Wire EDM (slow)±0.005 mmBetter surface finish, slower, more expensive
Jig grinding0.002 mmNot every shop has one
CMM measurement0.002 mmThis is measuring capability, not machining capability
A shop that quotes 0.002 mm for a milled pocket is either misunderstanding the question or planning to grind it afterwards. Ask which.

The three questions that expose a weak tolerance claim

1. Which feature?

A pin can hold 0.002 mm on its diameter after centreless grinding and 0.05 mm on the distance between two milled flats. A single number for the whole part is marketing. Ask for the tolerance per feature.

2. Measured how?

“0.002 mm” from a caliper is not the same as “0.002 mm” from a CMM in a temperature-controlled room. Ask what instrument produced the number, and ask to see a real inspection report.

3. Measured on every part, or on the first one?

First-article inspection is normal and acceptable. What matters is whether the report that ships with the batch shows actual values per piece, or a certificate of conformity that only says “passed”.

How to read a tolerance claim on a website

A claim worth trusting

Names the operation, the feature and the instrument. “Ground diameter to h6, straightness 0.01 mm over 100 mm, verified on a Hexagon CMM, inspection report requirements confirmed per order.”

A claim to be suspicious of

One number with no operation, no feature and no instrument. “Precision: 0.002 mm.”

What tighter tolerance actually costs

Tolerance is not free, and the cost is not linear:

Specifying 0.002 mm where 0.01 mm would function is one of the most common ways buyers overpay.

The honest version

We hold 0.002 mm on grinding and on CMM measurement, 0.005 mm on slow wire EDM and CNC, and ±0.01 mm on general milling. We will tell you which one applies to your feature before you order, not after.

Our sample inspection report shows the format — nominal, tolerance, measured value, per position.

Questions

Is 0.002 mm achievable on a CNC mill?

Not reliably in production. A well-set-up machine can reach ±0.005 mm on a good day, but holding 0.002 mm across a batch normally requires grinding after milling.

Do I need a CMM report with every order?

For critical features, yes. For standard components, a dimensional report on a sample is usually enough. Ask for per-piece values where the feature is functional.

Does temperature affect the measurement?

Yes. Steel expands about 11 µm per metre per degree Celsius. A 0.002 mm tolerance on a 200 mm part can be consumed by a 5 °C temperature difference between the part and the instrument.

Working on a part like this?

Send a drawing — STEP, IGES, DWG or a photo with dimensions. We reply within one business day with a DFM note and a price. One piece is acceptable for standard sizes.

Request a quote

Related components

Ejector Pins → Guide Pins → Wear Plates →

Keep reading

How to read an inspection report →SKD61 vs SKH51 vs SUJ2 →